Click here to
  Request more info.
Escalate Equipment Trailer. Model ET4000.
Bil-Jax 4,000 Lbs. Hydraulic lift trailer. Drop Deck.
Model 4000 offers one person operation, ground level deck lowering, towing ease, smooth ride fully loaded, quality painted finish, diamond tread-plated deck, and heavy duty construction for years of durable, reliable service.
Escalate Equipment Trailer. Model ET 4000

  Click here to
  Download this .PDF
Escalate Equipment Trailer. Model ET4000.
Bil-Jax 4
,000 Lbs. Hydraulic lift trailer. Drop Deck.
Model 4000 offers one person operation, ground level deck lowering,
towing ease, smooth ride fully loaded, quality painted finish,
 diamond tread-plated deck, and heavy duty construction for years of durable, reliable service.

Escalate Equipment Trailer. Model ET 4000
Operation and Service Manual
Patented
Load Capacity: 4000 lbs
The ET 4000 ESCALATE TRAILER offers ground
level roll-on loading and roll-off unloading of
equipment with
non-tilting lowering deck. The
hydraulic lift deck allows one person to load and
unload equipment.

Contents
SAFETY ............................................................... 2
SPECIAL FEATURES ......................................... 2
SPECIFICATIONS ................................................ 3
WARRANTY ......................................................... 3
TRAILER HITCHING ........................................... 4
EQUIPMENT LOADING ...................................... 5
SERVICE .............................................................. 7
PARTS LIST ........................................................ 10

B33-01-0069-01
®
®
Brought to you by:
Robert's Diesel Works Inc.
407-246-1597 or 800-341-1370
SAFETY
2
Warnings and Cautions
Observe all warning labels on
the trailer. The trailer warning
labels are shown here as a
reminder. Other warnings and
cautions are included in this
manual.
Failure to observe all warnings
may result in serious injury or
death. Failure to observe all
cautions may result in equipment
damage.

WARNING
Stand clear of trailer while deck is being raised or
lowered. Moving deck will create pinch points
causing serious crushing injury.

WARNING
Stand clear of trailer while deck
is being lowered. Contact with
trailer deck will cause serious
crushing injury.

WARNING
Trailer deck must be fully raised
with transport clamp locked
before towing trailer.
Failure to comply with these instructions
may result in serious personal injury or
death as well as damage to cargo.

SPECIAL FEATURES
The Bil-Jax ESCALATE TRAILER includes all the features of a heavy duty trailer, plus:
Escalator Deck and Hydraulic Lift Heavy Duty Tie-Down Brackets
Surge Brake Stow-away Trailer Jack

®
SPECIFICATIONS
3
ESCALATE TRAILER
Model Number ET 4000 Serial Number
Specifications
Rated Capacity 4000 lbs. (1814.4 kg) max.
Weight (Empty) 1910 lbs. (866.4 kg)
Overall Width 94 in. (238.8 cm)
Overall Length 185 in. (469.9 cm)
Overall Height (Bed Raised) 36 in. (91.4 cm)
Bed Height (Raised) 16 in. (40.6 cm)
Bed Size (Flat Surface) 54 in. wide x 96 in. long
(137.2 cm wide x 243.8 cm long)
Overall Bed Size
(Including Ramp)
54 in. wide x 120 in. long
(137.2 cm wide x 304.8 cm long)
Ramp Grade 6 degrees
Hitch Size 2 in. (5.08 cm) ball
Suspension Leaf Spring
Brakes Standard - Hydraulic Surge; Optional - Electric

WARRANTY
Bil-Jax warrants its trailers for one year from the date of delivery against all defects of material and
workmanship, provided the unit is operated and maintained in compliance with Bil-Jax's operating and
maintenance instructions; structural components are also warranted for one year. Bil-Jax will, at its
option, repair or replace any unit or component part which fails to function properly in normal use.
This warranty does not apply if the trailer and/or its component parts have been altered, changed, or
repaired without the consent of Bil-Jax or by anyone other than Bil-Jax or its factory trained personnel,
nor if the trailer and/or its components have been subjected to misuse, negligence, accident or any
conditions deemed other than those considered as occurring during normal use.
Components not manufactured by Bil-Jax are covered by their respective manufacturers warranties. A
list of those components and their warranties is available upon written request to Bil-Jax.
Bil-Jax shall not in any event be liable for the cost of any special, indirect or consequential damages to
anyone, product, or thing. This warranty is in lieu of all other warranties expressed or implied. We
neither assume nor authorize any representative, or other person, to assume for us any other liability in
connection with the sale, rental, or use of this product.

®
TRAILER HITCHING
4
Hook Up the Trailer
1. Raise trailer and lift ball latch. 2. Line up ball with hitch.
NOTE: The trailer hitch uses a 2 inch ball.
3. Lower hitch onto ball and close ball latch. 4. Raise and secure jack.
NOTE: Trailer frame should be level when hitch
is on ball. Adjust height of tow bar as needed.
Always raise and pin the jack before towing.

5. Hook safety chains and attach breakaway
cable.

6. Connect and check trailer lights.
Always cross safety chains below tongue.
Safety chains must hold tongue up if hitch fails.
Always check the tail lights and brake lights
before towing.

EQUIPMENT LOADING
5
Lower the Deck
NOTE: Trailer must be hitched to vehicle according to page 4 before lowering or raising the deck.
1. Turn power switch to ON position. 2. Hold toggle switch in DOWN position. Lift
latch handle and push handle back.

NOTE: The trailer frame should be on a level
surface when lowering the deck.

Load the Equipment
1. Load equipment so that the resulting tongue
weight is 15 to 20% of the total load.

2. Install tie-down straps to keep the load from
shifting. Use tie-down anchors shown.
Maximum capacity = 4000 lbs. Do not exceed. Always secure the load with tie-down straps
before towing. Failure to properly secure the
load may result in injury, death, or equipment
damage.
Do not hook tie-down straps on the roller
guides.

EQUIPMENT LOADING
6
Raise the Deck (trailer must be hitched to vehicle)
1. Turn power switch to ON position and hold
toggle switch in up position. Stop raising deck
when deck latch is on latch bar.

2. Verify that deck latch is on latch bar. Turn
power switch to OFF position.
Make sure people are away from the trailer
before raising the deck. Keep hands and feet
away from deck and rails. Hands and feet can
get crushed between the deck and frame.
If not clamped, the deck may fall during travel.
Always clamp the deck before towing. Failure to
clamp the deck may result in injury, death, or
equipment damage.

Towing and Backing the Trailer
1. After backing and before towing trailer on
highway, always check the position of the
backup lever. Make sure the backup lever is
in the TOWING position (up).
Trailer surge brake will not work when backup
lever is in BACKUP POSITION.

2. Before towing, check position of breakaway
cable. If cable is pulled, brakes will drag and
overheat. Check periodically on long trips.

BACKUP
POSITION
ONLY
TOWING
POSITION

SERVICE
7
Tire Maintenance Wheel Torque Requirements
At least once each week, use an accurate tire
pressure gage to check the air pressure in both
trailer tires. Inflate to the pressure recommended
by the tire manufacturer (located on the tire).
It is extremely important to apply and maintain
proper wheel mounting torque on your axle.
Wheel nuts should be retorqued after 50 miles
and 100 miles and periodically there after.
Low or uneven tire pressures will not properly
support a loaded trailer and could lead to
premature tire wear.
When replacing tires, it is important to use a tire
of appropriate size and load rating (75D-15).
Failure to maintain proper torque on the lug
nuts may result in the wheel shearing off of the
trailer, possibly causing an accident and
seriously damaging the equipment.
The tightening of the lug nuts should be
torqued in the sequence above.
Lug nuts should be torqued in stages:
Stage 1 Stage 2 Stage 3
25 Ft-Lbs 60 Ft-Lbs 100 Ft-Lbs
This procedure should be followed after each
time the tire is removed.

Lubrication (every 6 months)
Lubricate the following parts with clean motor oil or wheel bearing grease
where shown.
For additional brake operating and service instructions, refer to the Surge Brake Actuator Manual
provided with the trailer.

NOTE: Be sure that no grease is applied to brake pad.
Wheel Bearings Jack
Hitch Deck Latch

SERVICE
8
Hydraulic Fluid Levels
1. Remove cover from hydraulic pump. Check
fluid level in hydraulic reservoir.

2. Lower trailer deck. If oil level is below 3 inches
with deck down, add 1/2 quart of hydraulic oil.
Use BP type HLP-46 or 10w hydraulic oil.

NOTE: When trailer deck is raised, hydraulic
fluid level should be at least 1/2 of reservoir
volume.

3. Remove fill cap from surge brake reservoir.
Add DOT 3 brake fluid as needed to bring
fluid level to 1/2 inch below fill port.

FILL CAP
Battery
1. Use hydrometer to check battery charge daily
or weekly, depending on frequency of use. If
the battery charge drops below 25% of full
charge (S.G. below 1.155 as corrected to
80°F) the battery must be recharged. Refer to
step 2 before charging battery.

2. Check the electrolyte level weekly. If battery
charge is low, add water to bring electrolyte
level just above plates.
If battery is fully charged, add water to raise
electrolyte to full mark in each cell.

3. Charge battery at one of the following charge
rates. The slow charge rate is preferred.
22 hours @ 5 amps

25 hours @ 20 amps
22 hours @ 50 amps
SERVICE
9
Replacing the Lift Rollers
1. On a paved, level surface, pull trailer onto 4x6
blocks. Jack up and unhitch the trailer.

2. Lower the deck until the front or rear lift rollers
can be removed from the roller access holes.

3-1/2
The deck must be supported by the paved
surface or shoring before the lift rollers are
removed.

3. Loosen the setscrews that prevent the rollers
from backing out. The setscrews are located
on the trailer frame where the rollers thread
in. Use a socket wrench, with a 1 1/2" socket,
to unscrew and remove the rollers. Install and
tighten new rollers. Retighten the setscrews.

NOTE: It is easier to remove and replace one
roller at a time. You can adjust the jack to access
each roller.

PARTS LIST
10
Model ET 4000 E
SCALATE TRAILER, Hitch Section
Item No. Part No. Description Qty
1 B00-00-0114 Strap, Tie-Down, Battery Cover 1
2 B01-10-0150 Box, Battery (includes lid & strap) 1
3 0090-0188 Nut, Nylon Lock, 3/8-16 1
4 B01-01-0027 Cable, Battery, 19" 2
5 0090-0160 Nut, Hex, 5/16-18 1
6 B01-04-0002 Battery, 12 Volt, Deep Cycle 1
7 B01-02-0060 Switch, Master Power 1
8 B01-02-0019 Switch, Toggle 1
9 B06-00-0345 Decal, UP/DOWN 1
10 B01-10-0151 Light, Marker 2
11 B01-10-0152 Grommet, Marker Light 2
12 B01-10-0153 Plug Assembly, Marker Light 2
13 0090-0162 Nut, Hex, 3/8-16 1
14 B01-09-0026 Bushing, Hole 2
15 B01-09-0057 Bushing, Tube 4
16 B01-09-0018 Boot, Terminal 2
17 B01-01-0119 Cable, Battery, 55" 1
*18 B23-02-0046 Jack, Tongue 1
19 0090-0192 Hex Nut, Self-Locking, ½-13 1
20 B25-00-0062 Bushing, Flanged Sleeve 1
21 0090-0081 Screw, Cap, ½ -13 x 5 1
22 0090-0574 Washer, SAE Flat, ½ 6
23 B03-00-0017 Safety Chain Assembly 2
24 0090-0344 Screw, #10-24 x ½ 3
25 B01-01-0120 Harness, Wiring 1
26 0090-0192 Nut, Lock, ½-13 3
27 0090-0080 Screw, Cap, ½-13 x 4-½ 2
28 B12-00-0013 Hitch, Brake Surge Type, 2 in. 1
29 B21-00-0015 Kit, Brake Line 1
30 B04-07-0036 Clamp, Hose 1
31 0090-0183 Nut, Lock, ¼-20 1
32 B00-00-0112 Face Plate, Power Switch 1
33 B01-09-0050 Wire, Butt Splice 2
34 B12-00-0101 Kit, Brake-away Cable 1
* Jack assembly includes items 18, 19, and 20.

®

Model ET 4000 ESCALATE TRAILER, Hitch Section
®
PARTS LIST
12
Model ET 4000 E
SCALATE TRAILER, Lift Section
Item No. Part No. Description Qty
1 0090-0428 Washer, SAE Flat, ¾ 2
2 B07-06-1035 Bar, Deck Latch 1
3 0090-0147 Pin, Cotter, 1/8 x 1-¼ 2
4 0090-0689 Nut, Nylon Lock, 1-8 5
5 0090-0429 Washer, SAE Flat, 1 2
6 0090-0902 Screw, Cap, 1-8 x 7 1
7 B07-07-5010 Bar, Lift 1
8 B07-10-1087 Spacer, 1-7/32 in. 2
9 B12-00-0076 Link, Lift Multiplier 1
10 0090-0901 Screw, Cap, 1-8 x 6-½ 3
11 0090-0188 Nut, Nylon Lock, 3/8-16 6
12 B39-00-0031 Spring, Extension 2
13 0090-0422 Washer, SAE Flat, 3/8 2
14 B07-06-5353 Link, Latch 2
15 B07-06-5358 Deck Latch 1
16 0090-0049 Screw, Cap, 3/8-16 x 2-¼ 2
17 0090-0046 Screw, Cap, 3/8-16 x 1-¾ 4
18 B11-00-0040 Lever, Latch 1
19 0090-0040 Screw, Cap, 3/8-16 x ¾ 2
20 0090-0210 Washer, Split Lock, 3/8 2
21 B18-00-0130 Cover, Pump (includes top, bottom, & strap) 1
22 0090-0900 Screw, Cap, 1-8 x 5-½ 1
23 B02-03-0016 Hydraulic Cylinder 1
23A B02-13-0104 Seal Repair Kit, Hydraulic Cylinder 1
24 B02-02-0072 Fitting, Hydraulic 1
25 B02-01-0135 Hose, Hydraulic, ¼" dia. x 40" 1
26 B02-01-0026 Hose, Hydraulic, 3/8" dia. x 30" 1
27 B02-02-0070 Fitting, Hydraulic 1
28 B07-10-1086 Spacer 2
29 B01-09-0033 Wire End, Fork 3
30 B02-02-0017 Fitting, Hydraulic 1
31 B02-04-0002 Valve, Flow Control 1
32 B02-02-0185 Fitting, Hydraulic 1
33 B02-02-0072 Fitting, Hydraulic 1
34 B02-05-0023 Pump Assembly, Hydraulic 1
35 B00-00-0115 Strap, Tie-Down, Pump Cover 1
36 B46-00-0026 Grip, Handle 1


Model ET 4000 ESCALATE TRAILER, Lift Section ®
PARTS LIST
14
Model ET 4000 E
SCALATE TRAILER, Deck and Frame Section
Item No. Part No. Description Qty
1 B12-00-0061 Deck Weldment 1
2 0090-0060 Screw, Cap, 3/8-16
x 5-1/2
4
3 0090-0422 Washer, SAE Flat, 3/8 8
4 B30-00-0026 Spacer, Guide Bar 4
5 B11-00-0038 Guide Bar 2
6 0090-0188 Nut, Nylon Lock, 3/8-16 4
7 0090-0355 Setscrew, Cup Pt.
1/4-20 x 1/4
6
8 B12-00-0062 Frame Weldment 1
9 B25-00-0058 Roller, Lift 6
10 0090-0509 Screw, Cap, Nylon,
3/8-16 x 3/8
8
11 B06-00-0313 Decal, "Stand clear ..." 2
12 B31-00-0029 Wear Pad, Guide Bar 2
13 B01-10-0024 Light Assembly, Left Tail 1
13A B01-10-0023 Light Assembly, Right
Tail
1
13B B01-10-0070 Lamp, Tail Light,
GE-1157
2
13C B01-10-0069 Replacement Lens, Tail
Light
2
14 0090-0206 Washer, Split Lock, ¼ 4
15 0090-0159 Nut, Hex, 1/4-20 4
16 0090-0005 Screw, Cap, 1/4-20
x 3/4
2
17 B29-00-0037 Bracket, License Plate 1
18 0090-0419 Washer, SAE Flat, ¼ 2
19 0090-0183 Nut, Nylon Lock, 1/4-20 2
20 0090-0896 Nut, Lock, 3/8-16 10
21 0090-0042 Screw, Cap, 3/8-16 x 1 10
22 B10-00-0033 Brake Assembly,
Left-Hand
1
22A B10-00-0032 Brake Assembly,
Right-Hand
1
22B B10-00-0038 Brake Pad, Front 2
22C B10-00-0016 Brake Pad, Rear 2
*23 B12-00-0071 Wheel Assembly, 6 Lug 2
24 B25-00-0060 Bearing, Wheel, Inner 2
24A B25-00-0061 Bearing, Wheel, Outer 2
25 B32-00-0014 Seal, Bearing 2
26 B32-00-0013 Cap, Hub 2
27 0090-0624 Nut, Wheel Lug 12

 Wheel assembly includes items 24 through 27.
Item No. Part No. Description Qty
28 0090-0882 Washer, Wheel 2
29 0090-0880 Nut, Castle 2
30 0090-0881 Pin, Cotter, 5/32 x 2 2
31 B08-02-0003 Tire, 75D-15 (Outside
Diameter 27.59 Max.)
2
32 0090-0905 Bolt, 9/16-16 x 3-1/2 4
33 0090-0906 Nut, Lock, 9/16-16 4
34 B39-00-0033 Hanger Kit, Leaf Spring 1
35 B31-00-0028 Pad, Leaf Spring 2
36 B39-00-0032 Leaf Spring 2
37 B06-00-0317 Decal, Escalate Trailer
Logo
2
38 B06-00-0351 Decal, ET 4000 2
39 B06-00-0312 Decal, "Moving Deck ..." 2
40 B06-00-0344 Decal, Raise Bar, Press
Switch
1
41 Not
Replaceable
Plate, Serial # 1
42 0090-0033 Screw, Cap, 5/16-18 x
1-3/4
8
43 0090-0208 Washer, Split Lock, 5/16 8
44 0090-0420 Washer, SAE Flat, 5/16 8
45 B12-00-0082 Fender 2
46 0090-0183 Nut, Nylon Lock, 1/4-20 13
47 B04-07-0032 Clamp, Hose 11
48 B06-00-0347 Decal, 4000# Max. Cap. 1
49 B29-00-0147 Bracket, Side Marker
Light, Left Front/Right
Rear
2
50 B01-10-0021 Light, Side Marker,
Left/Right Front - Amber
2
50A B01-10-0066 Replacement Lens -
Amber
2
50B B01-10-0068 Lamp, Side Marker 2
51 B29-00-0146 Bracket, Side Marker
Light, Left Rear/Right
Front
2
52 B01-10-0022 Light, Side Marker,
Left/Right Rear - Red
2
52A B01-10-0067 Replacement Lens -
Red
2
52B B01-10-0068 Lamp, Side Marker 2

®

Model ET 4000 ESCALATE TRAILER, Deck and Frame Section ®
PARTS LIST
16
Model DB-1343 Hydraulic Pump Assembly

Item No. Part No. Description Qty
1 B02-15-0119 Coupling, SAE 9T-20/40 1.26 1
2 B02-15-0128 Ball, 0.375 Steel, G50 1
3 B02-15-0091 Seal, Shaft 0.500 x 1.00 x 0.25 1
4 B02-15-0201 Breather, Plastic 1
5 B02-15-0093 Washer, 0.338 x 0.625 x 0.60 Steel 3
6 B02-15-0166 Washer, Lock, 0.255 x 0.485 x 0.062 1
8 B02-15-0061 Magnet, Plumbing 1
9 B02-15-0121 Filter, 149 Micron 1.50 x 1 1
10 B02-15-0122 Motor, DC - 12V, 1T, Std. Duty 1
11 B02-15-0123 Screw, Taptite, 1/4-20 x 0.25, Hex 1
12 B02-15-0358 Screw, Taptite, 1/4-20 x 0.37, Hex 1
13 B02-15-0125 Cover, Suction, 3/8 NPT 1
14 B02-15-0126 Screw, Taptite, M6 x 1, 12 mm 2
15 B02-15-0345 Solenoid, Smart Start, 12VDC 1
17 B02-15-0197 Cartridge, Check Valve 1
18 B02-15-0170 Screw, 5/16-18 x 1.00 Torx 1
19 B02-15-0359 Bolt, M8 x 75 MM, Hex 2
20 B02-15-0360 Spring, RV 1000-2000 PSI Green 1
21 B02-15-0349 Coil, Solenoid, 12VDC, 2 Pin 1
22 B02-15-0199 Bolt, #12-24 x 0.50 Hex Washer 4
23 B02-15-0114 Pin, 1/8 x 1/4 1
24 B02-15-0073 O-Ring, 2-348 Buna 1
26 B02-15-0355 Wiring Assembly, 4 Pin 1
27 B02-15-0356 Endhead, Finished 1
28 B02-15-0078 Pump Assembly, 1.6 Short Spline 1
29 B02-15-0206 Tank, Plastic, Horizontal Mount w/Drain 1
30 B02-15-0030 Cap, Relief, Assembly (B-2) 1
31 B02-15-0195 Plug, Plumbing, 9/16 SAE 1
32 B02-15-0204 Plug, Plumbing, 1/16 NPT Flush 2
33 B02-02-0059 Nylon Ell (X-111) 1
34 B02-15-0026 Screw, Valve, Adjustment 1
35 B02-15-0357 Valve Cartridge, Relief, Normally Closed, w/o Coil 1
36 B02-15-0102 Nameplate, Fenner Serial 1

PARTS LIST
17
Model DB-1343 Hydraulic Pump Assembly

Brought to you by:
Robert's Diesel Works Inc.
407-246-1597 or 800-341-1370
Model ET 4000
ET4000
Bil-Jax Trailers
Robert's Diesel Works Inc.
Visit our store at Truck-Parts-Auction.Com
4000 Lbs drop deck trailer
Escalate 4000 Lbs trailer
ET4000
Bil Jax 4000 ET
4000ET
4000 ET drop deck
ET4000 Trailer
Drop Deck Trailer
4000 Lbs Drop Deck Trailer
Equipment Trailer
Drop Deck Equipment Trailer
Drop Deck Trailer
   Equipment
PM Cranes
Robert's Diesel Works Inc.
407-246-1597
RSS Feed
Google-Translate-Chinese (Simplified) BETA Google-Translate-English to French Google-Translate-English to German Google-Translate-English to Italian Google-Translate-English to Japanese BETA Google-Translate-English to Korean BETA Google-Translate-English to Russian BETA Google-Translate-English to Spanish